A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
The writer is making several good points on Tools You Need to Install a New Bathtub in general in this content down the page.
Setting up a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a new one is also a moderately challenging job. If the old bathtub is easily accessible, the task can relocate speedily; if you have to open up a wall to get rid of the old bathtub and also place the new tub, the task is much harder. In either instance, the job is within a residence handyman's abilities, although you will certainly need a helper to leave the old tub as well as set in the new one. Ensure you have actually certified on your own for the job and also are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed task, it is much better to think about employing one before you start. Possibilities are you might need an expert plumber to make tube connections.
This write-up will assist you mount a brand-new tub in your restroom if you have actually currently purchased a new tub and also do not need to alter the plan of your previous water supply pipelines.
Your tools as well as product list must make up the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The process of eliminating the existing faucets can be fairly bothersome due to the limited gain access to that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will originate from the pipes. Once the supply pipes have actually been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Before going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will require a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in area in between the tap as well as the sink. Protect the faucet in place with the manufacturer supplied backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The previous type should be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of the two wooden boards under its feet, place the tub in the called for setting. The wood boards are helpful in uniformly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The following goal is to make sure that the tub is leveled all round. This can be achieved by examining the level and changing the feet on the bath tub until the spirit level reads level.
To set up faucets, fit the bottom of the outermost adaptable faucet adapter to the suitable supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Activate the water supply and check all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub and also examine the overflow outlet and also the typical outlet for leaks.
Finally, deal with the bath paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub ought to wait till the tub has been utilized at the very least once as this will certainly resolve it into its last placement.
Getting ready for the Setup
To start with, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to stop strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should now be ready to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to crack an inflexible seal, creating the water to pass through the wall in between the bath and also the tiling, leading to difficulties with moisture as well as feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and installations. They are offered in tubes and cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can split rather very early if you do not consider this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were shown that editorial on Installing A Bathtub from a friend on our other web blog. Be sure to take the opportunity to promote this blog posting if you enjoyed reading it. Thank-you for your time spent reading it.
Stress-free fix? Contact. Report this page